xref: /arm-trusted-firmware/plat/mediatek/mt8183/drivers/mcsi/mcsi.h (revision 91f16700b400a8c0651d24a598fc48ee2997a0d7)

/*
 * Copyright (c) 2019, ARM Limited and Contributors. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#ifndef MCSI_H
#define MCSI_H

#define SLAVE_IFACE7_OFFSET		0x1700
#define SLAVE_IFACE6_OFFSET		0x1600
#define SLAVE_IFACE5_OFFSET		0x1500
#define SLAVE_IFACE4_OFFSET		0x1400
#define SLAVE_IFACE3_OFFSET		0x1300
#define SLAVE_IFACE2_OFFSET		0x1200
#define SLAVE_IFACE1_OFFSET		0x1100
#define SLAVE_IFACE0_OFFSET		0x1000
#define SLAVE_IFACE_OFFSET(index)	(SLAVE_IFACE0_OFFSET + \
							(0x100 * (index)))
/* Control and ID register offsets */
#define CENTRAL_CTRL_REG		0x0
#define ERR_FLAG_REG			0x4
#define SF_INIT_REG			0x10
#define SF_CTRL_REG			0x14
#define DCM_CTRL_REG			0x18
#define ERR_FLAG2_REG			0x20
#define SNP_PENDING_REG			0x28
#define ACP_PENDING_REG			0x2c
#define FLUSH_SF			0x500
#define SYS_CCE_CTRL			0x2000
#define MST1_CTRL			0x2100
#define MTS2_CTRL			0x2200
#define XBAR_ARAW_ARB			0x3000
#define XBAR_R_ARB			0x3004

/* Slave interface register offsets */
#define SNOOP_CTRL_REG			0x0
#define QOS_CTRL_REG			0x4
#define QOS_OVERRIDE_REG		0x8
#define QOS_TARGET_REG			0xc
#define BD_CTRL_REG			0x40

/* Snoop Control register bit definitions */
#define DVM_SUPPORT			(1U << 31)
#define SNP_SUPPORT			(1 << 30)
#define SHAREABLE_OVWRT			(1 << 2)
#define DVM_EN_BIT			(1 << 1)
#define SNOOP_EN_BIT			(1 << 0)
#define SF2_INIT_DONE			(1 << 17)
#define SF1_INIT_DONE			(1 << 16)
#define TRIG_SF2_INIT			(1 << 1)
#define TRIG_SF1_INIT			(1 << 0)

/* Status register bit definitions */
#define SNP_PENDING			31

/* Status bit */
#define NS_ACC				1
#define S_ACC				0

/* Central control register bit definitions */
#define PMU_SECURE_ACC_EN		(1 << 4)
#define INT_EN				(1 << 3)
#define SECURE_ACC_EN			(1 << 2)
#define DVM_DIS				(1 << 1)
#define SNOOP_DIS			(1 << 0)

#define MSCI_MEMORY_SZ			(0x10000)

#define MCSI_REG_ACCESS_READ		(0x0)
#define MCSI_REG_ACCESS_WRITE		(0x1)
#define MCSI_REG_ACCESS_SET_BITMASK	(0x2)
#define MCSI_REG_ACCESS_CLEAR_BITMASK	(0x3)

#define NR_MAX_SLV			(7)

/* ICCS */
#define CACHE_INSTR_EN			(1 << 2)
#define IDLE_CACHE			(1 << 3)
#define USE_SHARED_CACHE		(1 << 4)
#define CACHE_SHARED_PRE_EN		(1 << 5)
#define CACHE_SHARED_POST_EN		(1 << 6)

#define ACP_PENDING_MASK		(0x1007f)

#define CCI_CLK_CTRL			(MCUCFG_BASE + 0x660)

#ifndef __ASSEMBLER__

#include <plat/common/common_def.h>
#include <stdint.h>

/* Function declarations */

/*
 * The MCSI driver must be initialized with the base address of the
 * MCSI device in the platform memory map, and the cluster indices for
 * the MCSI slave interfaces 3 and 4 respectively. These are the fully
 * coherent ACE slave interfaces of MCSI.
 * The cluster indices must either be 0 or 1, corresponding to the level 1
 * affinity instance of the mpidr representing the cluster. A negative cluster
 * index indicates that no cluster is present on that slave interface.
 */
void mcsi_init(unsigned long cci_base,
		unsigned int num_cci_masters);
void mcsi_cache_flush(void);

void cci_enable_cluster_coherency(unsigned long mpidr);
void cci_disable_cluster_coherency(unsigned long mpidr);

void cci_secure_switch(unsigned int ns);
void cci_init_sf(void);
unsigned long cci_reg_access(unsigned int op, unsigned long offset, unsigned long val);

#endif /* __ASSEMBLER__ */
#endif /* MCSI_H */